[AI] strange problem with k1000.

Mahesh Panicker maheshspanicker at gmail.com
Sun Feb 17 01:26:15 EST 2008


Hello Viraj.
I am trying the steps you have suggested.
another thing I have noticed is that when you keep the automatic corrections
disabled, such mistakes are also reduced.
regards.


On 2/17/08, Viraj <vkafle at gmail.com> wrote:
>
> One thing I forgot to mention. Having edited the corrections list, be sure
> to apply it in the document by clicking Apply Corrections in the Tools
> menu.
> You'll get the option only when a file is open.
> ----- Original Message -----
> From: "Viraj" <vkafle at gmail.com>
> To: <accessindia at accessindia.org.in>
> Sent: Sunday, February 17, 2008 11:03 AM
> Subject: Re: [AI] strange problem with k1000.
>
>
> >I have faced such problems even in earlier versions and have been unable
> to
> >come up with definite solutions. However, one can try the following:
> >
> > 1. Switch to Fine reader engine if one is using RTK or Scansoft.
> > 2. Try switching to Grey Scanning mode.
> > 3. Click Edit Corrections in the Tools menu, press Add, enter the word
> as
> > it is being recognised, such as, odier, and press OK. Now enter the
> > correct word, (other in this instance). Edit all other words that often
> > gets misrecognised in the same way. But sometimes this can result in the
> > replacement of actually correct words with wrong words. For instance, if
> > the program learns to recognise all di as th, then actual words with di
> > will also be converted into th (like the word die will be converted into
> > the). However, what one can do (though it does not guarantee 100 per
> cent
> > success) is to enter the entire word in the edit corrections list,
> instead
> > of letter combination, for instance, odier and other instead of di and
> th.
> > 4. One can also try the Replace All command (control H). But here also
> one
> > should be careful to replace the entire wrong word instead of letter
> > combinations, else one will get wrong results. one can try enabling the
> > Match Whole Word option in the Rplace dialogue box.
> >
> > One can never hope that issues wil be resolved for good through these
> > steps, but one can always try.
> >
> >     Please note that the menu commands described above are based on
> > version 9. Look around if version 11 has different menu arangements.
> > ----- Original Message -----
> > From: "Mahesh Panicker" <maheshspanicker at gmail.com>
> > To: <accessindia at accessindia.org.in>
> > Sent: Saturday, February 16, 2008 9:48 PM
> > Subject: [AI] strange problem with k1000.
> >
> >
> >> Hi list.
> >> I am facing a strange problem with Kurzweil1000 version 11. when I scan
> a
> >> document, the letter combination TH gets recognized as DI. for EG, the
> >> word
> >> that gets recognized as diat.
> >> what can be the sorce of this particular problem? how can it be
> >> addressed?
> >> looking forward to your suggestions.
> >> thanks in advance.
> >>
> >>
> >> --
> >> Mahesh S. Panicker
> >> room no. 121;
> >> Kaveri-hostel;
> >> Jawaharlal Nehru university new delhi 110067 india.
> >> To unsubscribe send a message to accessindia-request at accessindia.org.in
> >> with the subject unsubscribe.
> >>
> >> To change your subscription to digest mode or make any other changes,
> >> please visit the list home page at
> >>
> >>
> http://accessindia.org.in/mailman/listinfo/accessindia_accessindia.org.in
> >
>
>
> To unsubscribe send a message to accessindia-request at accessindia.org.inwith the subject unsubscribe.
>
> To change your subscription to digest mode or make any other changes,
> please visit the list home page at
> http://accessindia.org.in/mailman/listinfo/accessindia_accessindia.org.in
>



-- 
Mahesh S. Panicker
room no. 121;
Kaveri-hostel;
Jawaharlal Nehru university new delhi 110067 india.



More information about the AccessIndia mailing list